PS-x 系列電源用于將 230Vac 或 24Vac 轉換為穩定的 24Vdc 輸出，提供保護、自診斷和自檢功能。具有過流和過壓保護、各種條件的 LED 指示、用于輸入丟失的可選警報繼電器輸出和 PCB 上的復位按鈕。

它們適用于需要為傳感器或 IO 模塊提供輔助電源的應用。

LED指示

打開

當 PSU 通電時，LED 將呈橙色常亮顯示約 0.5 秒。（如果在加電過程中按下復位按鈕，它會在這一步保持裝置。）大約 0.5 秒后，輸出被啟用并且警報繼電器關閉。該狀態保持 5 秒，或直到輸出電壓達到22.0Vdc。

當輸出電壓在范圍內時，繼電器保持閉合，并且 LED 顯示穩定的綠色。如果未達到最小電壓，則輸出關閉，繼電器打開。LED 呈橙色長短閃爍，直到按下復位按鈕。

復位按鈕

每當按下復位按鈕時，LED 呈橙色常亮，輸出關閉，繼電器打開。

輸出超出限制

如果輸出電壓低于 22.0Vdc，LED 會短時閃爍橙色。繼電器保持關閉 4 秒。如果輸出電壓足夠低足夠長時間，輸出電壓關閉，繼電器打開，LED 呈橙色長短閃爍，直到按下復位按鈕。如果輸出電壓升至 25.0Vdc 以上，則 LED 以紅色短-短-短閃爍。繼電器保持關閉 1 秒。如果輸出電壓足夠高且持續時間足夠長，則輸出電壓關閉，繼電器打開，LED 呈紅色長短短閃爍，直到按下復位按鈕。

• LED 故障指示
• PCB自檢功能
• DIN 導軌安裝
• 故障查找 LED 指示
• 報警輸出